恒泰源聚氨酯

Мы специализируемся на производстве полиуретана для обувной подошвы

>
>
>
Жидкость на подошвах полиуретановой обуви средней плотности

Жидкость на подошвах полиуретановой обуви средней плотности

Товарный код
Количество
-
+
Наличие на складе :
Product description
Параметры

 

浙江恒泰源聚氨酯有限公司生产的中高密度鞋底原液主要包括中高密度中硬度聚氨酯鞋底原液、中高密度低硬度聚氨酯鞋底原液、中高密度高硬度聚氨酯鞋底原液。尤其是中高密度中低硬度聚氨酯鞋底原液在连帮鞋上用量很多,在南美和中东地区销售量很大,而且客户对中高密度中低硬度聚氨酯鞋底原液评价一直很好。

牌号( Shop sign): ZG-P-5005/ZG-I-5320

中高密度中低硬度聚氨酯鞋底原液的特性:

Medium and high-density PU Resin for shoe sole with the upper

1. 特性:中低硬度,中高密度

Characteristic: Medium and low hardness, medium and high density

2. 用途:适用于男女连帮鞋底的生产

Application: Applicable to the production of shoe sole with the upper for men and women

               中高密度中低硬度聚氨酯鞋底原液

             中高密度中低硬度聚氨酯鞋底原液

3. 原液特性 Typical properties of PU Resin

  品 名

Name of products

  外 观

Appearance

粘 度Viscosity(Pa·s/50℃) 密 度Density(g/cm3/40℃) 包 装Package(kg)
  ZG-P-5005 白色或淡黄,液状无异物White or paleyellow, liquid, no foreign material   0.50-0.80   1.16-1.20   18
 ZG-I-5320 透明液体无异物Transparent liquid, no foreignmaterial   0.20-0.40   1.18-1.20   20

参考发货配比(Reference shipments ratio):A/B=30/25(桶) Reference shipments ratio: A/B=30/25 (barrel)

 

4. 成型条件及物性值(Molding conditions & physical properties):

测试项目Test item 参考物性值Reference physical properties
鞋底成型密度Molded density of sole(g/cm3 0.35~0.45
硬度(A型)Hardness (type A) 35~45
拉伸强度Tensile strength(MPa) 5.0~7.0
伸长率Elongation(%) 300~400
NBS耐磨NBS abrasion resistance(%) ≥10%
自由泡密度Free foam density(g/cm3 0.30~0.40
耐折性(常温)(4万次裂口长度,mm)Folding endurance (room temperature)(40,000 gap length mm) <8

●配合比率是以最佳配比值为基础,此配比值会随添加的颜料助剂种类和添加量不同而变化。

Matching ratio is based on the optimal matching value which will vary with the category and additive amount of paint additives added.

●自由泡沫密度会依季节(温度,湿度)的不同而变化。

Free foam density will vary with the seasons (temperature, humidity).

●脱模时间会随成型品厚度的增加而延长。

Stripping time will be extended with the increase of the thickness of moldings.

●耐折条件:屈挠角度为 90度,频率为80次/min*4万次。

Folding endurance conditions: bending angle is 90 degrees and the frequency is 80 times / min * 40 thousand times

● 以上数据仅作参考,具体数据以实际操作为准。如需其他物性指标,请与我公司联系。

Data listed above is just for reference. The specific data is subjected to the practical operation. If other physical properties are required, please contact us.

Соответствующая группа параметров не найдена, добавьте ее в шаблон со свойствами в фоновом режиме

Адрес:
Индустриальный парк 1 - й дороги, уолин, провинции чжэцзян

       

EN     ES
中文   PT

Copyright © ООО «Производство полиуретана HeadSpring (Чжэцзян)»  浙ICP备20019453号 

中文 |EN | PT | ES | RU

搜索
Поиск